DURAFIX CAST ALUMINUM

Then Don’t worry — your e-mail address is totally secure. If the hole is a bit to big ,fill it in with JB-weld let it harden and then do the helicoil. I have a 5hp evinrude outboard and i made the mistake at trying to remove the exhaust manifold plate and snapped off a bunch of screws. Follow the instructions exactly and remember that cleanliness is the key to this stuff bonding properly. Mark Channels Read Calendar. Just like when soldering copper pipe.

Unless you have big time welding equipment. Subscribe To This Site. The key step is to scratch the rod on the surface to break through the aluminum oxide coating and make the metal flow like solder. I have repaired two more [refrigeration] coils with Durafix since. This stuff sounds too good to be true. Hooty’s helicoil is by far more effective,faster and cheaper.

Durafix aluminum welding rods will repair tons of stuff. Impartial buying advice Speak to a trained technitian on Throw away the propane torch.

Announcement

It’s just a normal part of shop life. Has anyone used durafix on cast aluminum MAP gas rocks. A low working temperature of F C.

For some simple repairs like replacing an ear or lug that got broken off by a forklift or something, using Dura fix easyweld rods make for much less headache.

Has anyone used durafix on cast aluminum well rolmops, you don’t need welding equipment, only propane, but you do need the right tip to get the heat where you need it.

Has anyone used durafix on cast aluminum Page: 1 – iboats Boating Forums |

Technically it is not welding. Has anyone used durafix on cast aluminum August 6th, August 10th, Unless you have big time welding equipment. Just use minumum heat and stop often. No need for years of welding experience. August 8th, No flux is needed Hooty’s helicoil is by far more effective,faster and cheaper.

  HEATKILLER HTF4 SERIES RADIATOR

About Us Contact Us Shopping cart is empty. August 9th, I am both pleasantly pleased and surprised to say that your product worked flawlessly! I charged the system and it has been leak free and blowing cold air since!! You can set it by just drilling your hole to the right size threading the hole and inserting it.

H eat until it starts to flow. Subscribe To This Site.

But the end result is sometimes a better repair than could be made with a TIG welder. Welding and Brazing Rods. Seasoned welders sometimes overlook this easy method to weld repair items like alternator housings, aluminum boats,etc.

Durafix Reviews Aluminum Welding Testimonials

There is no need for expensive equipment. None have leaked at the repair.

I am trying to completely overhaul this engine on a budget that doesnt include a trip to the machine shop. Tig welding small gun parts. Grind damaged edges to a 45 bevel.

Durafix works on most aluminium, zinc, copper, brass, pot-metal and die-cast aluminium. Once the repair is made and cooled offit can be casy, filed, drilled, tapped etc and is often stronger than aluminm base material. But before you throw something away, you might just save time and money with Dura-Fix. In fact you can use it on almost any non-ferrous metal, except stainless steel.

  GHOST WHISPERER SEASON 1 EPISODE 11 SHADOWBOXER

Welding and Brazing Rods

I send out emails about once a week or so when I find a good video on welding. Has anyone used durafix on cast aluminum I’d install a Heli-Coil. Akuminum had 11 leaks 0 leaks now. Be sure to kick rod into weld to break down skin resistance as filler rod will lay on surface and will not fuse if only heat is applied.

It’s convenient and can be used by both novice and professional alike. H eat the parts hot enough to flow without the aid of the flame, thoroughly tinning the surface. The key step is to scratch the rod on the surface to break through the aluminum oxide coating and make the metal flow like solder. The hole was for the ohc and needed to be torqued down to 30 pounds, is still working 2 years on from the repair.

Subscribe to our emails For the latest news, offers and info. You made a believer out of me and I will highly recommend your product whenever I am afforded the opportunity!!!! B rush surface to be repaired thoroughly under heat to break up surface oxide.

Related Posts