TRANE TCONT800 SERIES THERMOSTAT

Choose 1 if getting temperature overshoot. Failure to follow the instructions can damage the product or cause a hazardous condition. Through Nexia Diagnostics, your trusted dealer can remotely monitor your air conditioner, furnace and entire HVAC system to ensure optimal performance and prevent minor issues from turning into major repairs, ensuring the highest level of service. Deluxe programmable heat pump thermostat 68 pages. Others have modular stages of heat, similar to a dimmer lightswitch that has more flexibility. Select 7 available — Not shown if system selection is heat pump. The LO Battery indicator flashes in the display one month before the batteries run down completely.

When installing in a single transformer system, keep the jumper wire between the R and Rc screws. To unlock screen, see Advanced Settings section. Remote Temperature Sensor Outdoor or Indoor 0 No remote 1,3 temperature sensor 1—outdoor temperature sensor for display only. Thermostats and Controls Manage your thermostat, heating and cooling, and much more using your smart devices, wherever you are. Page 45 Step 9. Comfort control minimum off-time is activated. Failure to follow the instructions can damage the product or cause a hazardous condition.

The upper or lower temperature limits were reached.

Cycles per hour cph for 1st Stage Compressor 3 Compressor Stage 1 cycles per hour cph tcont00 3 is recommended. Temperature settings do not change. To unlock screen, see Advanced Settings section. Selecting terminal identifications for system type. To set a Program Schedule for the remaining days of the week, repeat steps Don’t have an account? Days Up and Down arrows appear for approximately seven seconds. Align the terminal screw blocks with the pins on the back of the comfort control.

Press Edit key to change the Timer reload value. Page 8 Editing Schedule 1. When using batteries, make sure positive and negative terminals are oriented correctly, as marked on the device. While in System Test mode, minimum off -time for compressors is bypassed.

  THENMERKU PARUVAKATRU MOVIE ONLINE

Clock Format 12 hour clock format 24 hour clock format Extended Fan on time Heat 0 No extended fan operation after call for heat ends 90 Fan operation is extended Not shown if fan 90 seconds after call for heat operation is set to ends. Symptom Possible Cause Action Display does not come on.

Thermostats and Controls

If your model has this feature, the humidity level in the home is shown in the lower right corner of the Home Screen. Using battery power only may not provide adequate power to comfort control and can cause damage during freezing conditions. Got it, continue to print.

By pressing ‘print’ button you will print only current page. Page 7 Table 1.

But you can change these settings to match your lifestyle: Then the comfort control internal temperature sensor is not used. Page 45 Step 9.

Time is not automatically adjused for Daylight Savings in Fall and Spring.

Trane Tcont Series Touch Screen Programmable Comfort Control Thermostat | eBay

When comfort control is first powered, display is ready to enter calendar date. Selection in this stage changes default cph for 2nd stage heat. See Advanced Settings, steps 8 through 10, for approximate calendar days. The Installer Test is part of Installer Setup options. Check Installer Setup Number to change keypad locked options.

Temperature Control in Cool 2 Standard 1, 3 temperature control in cooling 1—less aggressive temperature control could cause temperature undershoot 3—more aggressive temperature control could cause temperature overshoot Applies to recovery ramp.

Programmable thermostats can be set for multiple days at a time, so you don’t have to worry about adjusting the temperature each morning and night.

The bar above the selected period is removed, indicating the scheduled period was cancelled. Comfort control does not respond when touchpad is pressed. The keypad is fully locked.

Connected Controls

From the Home Screen, press the System key. Pressing a locked key while Screen Locked is shown flashes Screen Locked on the screen. Connect the 24 Vac Common B wire from the system transformer to the comfort control for proper operation when the battery power is drained. Emergency Maintenance Seasonal Maintenance. Select 7 available — Not shown if system selection is heat pump. Insert the trans screws into the holes and tighten. Failure to follow the instructions can damage the product or cause a hazardous condition.

  NEPALI MOVIE AAMA KO KAKH PART 12

Set system Selection to correct position. Page 52 American Standard Inc. Selecting Location Install the comfort control about 5 ft. Through Nexia Diagnostics, your trusted dealer can remotely monitor your air conditioner, furnace and entire HVAC system to ensure optimal performance and prevent minor issues from turning into major repairs, ensuring the highest level of service.

Auto default position —fan runs with equipment. To reinstate a schedule period, press arrow keys to set desired time and temperatures. When installing in a two-transformer system, use the common from the cooling transformer to connect to the B screw and remove the jumper wire between the R and Rc screws.

Comfort control screen is locked. Daylight Savings On or Off. Page 50 Sfries get to choose the connected control or the traditional thermostat that’s right for your home. Using the Comfort Control Schedule Period 2. M Select set of terminal identifications Table 2 that corresponds with system type conventional or heat Fig. If Mon – Fri was selected first, go back and repeat steps for Sat and Sun. Page 31 Reminder Timers Select Models These reminders notify you when to change your thermosgat filter, humidifier pad.

Related Posts